Your over-the-range microwave is humming but the food stays cold, or it threw sparks and a puff of smoke. Call Acdc Appliance Repair and we connect you with a licensed, insured independent pro near Wesson who services OTR, built-in and drawer microwaves.
A microwave is not a toaster. Inside the cabinet sits a high-voltage capacitor that can hold a lethal charge long after the plug is pulled, which is why this repair belongs with a trained technician and never with a screwdriver and a video.
We run a free referral line for homeowners. A dispatcher hears what the microwave is doing and connects you with an independent local technician who knows both the high-voltage side and the installation side of these units.
The contractors in our network are independent businesses that carry the license and insurance local rules require. Ask to see both at the door.
A magnetron or control board for a built-in can be a real expense. The technician writes the quote before any work starts, so you can compare it to a replacement unit and decide.
We look for a pro already working near Wesson. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
The right pro arrives with an insulated capacitor discharge tool, a meter for testing the diode and transformer windings, the tech sheet for your model, and a survey meter to confirm no leakage once the repair is done.
This is the work we route for OTR, wall-mounted, drawer and convection combo microwaves. Every job starts by safely bleeding the capacitor before a single meter lead goes in.
The fan spins, the light glows, the plate turns, and the coffee comes out cold. The usual suspects are the magnetron, the high-voltage diode, the capacitor, or the transformer. The technician tests each one with the power off and the capacitor discharged.
Sparking inside the oven often traces to a food-soaked waveguide cover, bare metal where the cavity paint chipped, or a worn rack support in a combo unit. Ignoring it can scorch the cavity and kill the magnetron.
The door has several interlock switches and a monitor switch that blows the line fuse if the others fail. A totally dead microwave often means that fuse did its job. If yours runs with the door open, unplug it now and do not use it again until it is checked.
Dead buttons, phantom beeps, or a unit that keeps running after the timer ends point to the membrane touchpad or a stuck relay on the control board. The technician reads the keypad circuit with a meter and checks the relays before ordering parts.
Because an OTR unit doubles as the hood over your cooktop, the vent side wears out too. The technician can replace a noisy fan motor, a burnt cooktop lamp, clogged grease filters, and the charcoal filter used on recirculating setups.
If the turntable sits still, the motor or the drive coupler is the likely culprit. An OTR microwave that tilts forward or shifts may have a loose mounting plate or top bolts that stripped the cabinet, and that needs attention before it drops onto the range.
Use this as a quick read before you call. Share what you see with the dispatcher, and the technician can bring the most likely parts.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
Most pros will be honest that a small countertop unit is cheaper to replace than repair. Over-the-range, built-in, drawer and convection combo models are different: they are pricier, they are sized to a cabinet opening or wall plate, and replacing one can mean new trim, new brackets and reworked ductwork.
Leave the cabinet closed and pick up the phone. The dispatch line is answered around the clock.
Tell the dispatcher what type of microwave you have, whether it sits over the range, in a wall, or in a drawer, and what it is doing. If you can, read off the model number from the tag inside the door frame.
We route the job to an independent pro near Wesson and give you the arrival window on the call. When the schedule cooperates, a technician often arrives the day you call.
First comes a safe discharge of the capacitor, then meter tests on the magnetron, diode, transformer, door switches and board. An OTR unit sometimes has to be lifted off its mounting plate. The written, upfront quote comes before any work begins, and you decide.
Once the part is in, the technician runs a water heating test and, if the high-voltage side was opened, checks the door edges with a leakage survey meter. The technician typically documents the parts and labor warranty on the work order; ask for a copy.
The OTR unit died with no display at all. The pro found the line fuse blown and a failed interlock switch behind it. He replaced the switch and the fuse together and explained that a fuse alone would have popped again within a week.
Our wall-mounted microwave ran with no heat. Replacing it meant matching a trim kit, so I asked about repair. She tested the high-voltage parts, swapped the magnetron, and ran a leakage check with a survey meter before packing up.
Sparks were jumping off the side wall every time I warmed soup. It was a burnt waveguide cover soaked with grease. Quick fix, and he showed me how to keep that cover clean.
The drawer microwave kept running even at zero, which scared us. The technician diagnosed a stuck relay on the control board, ordered the exact board, and installed it on a return visit.
A microwave that runs without heating has a fault in its high-voltage section: magnetron, diode, capacitor or transformer. Because that circuit can hold a deadly charge, the testing belongs with a pro who knows how to discharge it safely.
No. Stop using it until it is checked. Sparks usually come from a dirty or burnt waveguide cover or chipped cavity paint, and continued arcing can damage the magnetron. If there is smoke, keep the door closed and unplug it if you can reach the cord safely.
Most of the time a dead microwave has blown its line fuse, and the fuse blew because a door switch failed and the monitor switch tripped it. A good pro replaces the failed switch along with the fuse, not just the fuse.
Frequently. Over-the-range and built-in units are expensive and fitted to the opening, so a new one brings its own installation costs. Small countertop models are usually better replaced. With a written quote from the pro in hand, you can make the call.
We strongly advise against it. That capacitor stores enough energy to kill, even with the plug pulled. Keep the outer case on and leave the discharge to a technician with proper insulated tools.
You should request it after any magnetron, door or high-voltage repair. Many technicians run a survey meter around the door edges and vents as a final check that nothing is leaking.
Our line connects homeowners and renters across Wesson and the surrounding area with independent microwave technicians. Calls go to whoever has a route nearby, and that matters when an over-the-range unit has to be taken down for service.
The dispatch line is open 24 hours a day. A late-night call is usually booked for the next morning, and daytime calls often turn into same-day visits when a local pro has an opening.
